Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - tawny

Pages: [1]
1
Installation issues / Phone calls cutting off
« on: July 13, 2010, 05:48:47 pm »
I have a sipgate connection, but calls are disconnecting on both inbound and outbound.

Have called sipgate, and they say that I am sending them a 'BYE' after 5 minutes.

Anyone know why it would be doing this?

2
Installation issues / CCTV advice
« on: July 04, 2010, 05:46:43 pm »
I have a 'Higheasy 170X' 8 (or could be 16) channel H.264 capture card that I've put into my LMCE core.

Looking for the best way forward, in particular:

1. How to install drivers for it (and where to get them from??!) and test

2. What software is built into LMCE? (I know there is CCTV support, but is this 'out of the box', or should I be adding software to it. I have read about 'Zoneminder' which seems good, so should I install this if it isn't already?

Apologies if I'm wide of the mark, or missing info which is readily available here - I'm trying to assimilate info that I have picked up in various places and am now confusing myself; desperate for a little hand holding!

Thanks
:)

3
Users / Incoming call routing
« on: June 15, 2010, 07:47:11 pm »
Really don't get this! Can someone please clear this up for me:

At present, only two phones ring on incoming trunk calls, and then go to the generic 'press x for all phones in house' etc.

I want to:

1) Make ALL phones ring
- I have looked at the default inbound route in FreePBX (custom app, with a string pointing to somewhere in pluto). Can't find any reference to this in Linux MCE. Have got a group that 'rings all', 600, but can't seem to point the inbound route to this as it won't let me??!

2) Either change the IVR or remove it.
- I've found the call routing section of LinuxMCE but cannot understand it as it refers to people rather than trunks etc. Maybe I'm missing something but...? Also, here I have tried setting '# of seconds to ring before ivr' to zero and also 99 in an attempt to disable it but nothing! Why am I feeling stupid right now?


4
Users / Cisco 7970 phones
« on: May 21, 2010, 01:00:18 am »
Hi all

Got my 7970 handsets working brilliantly (on SCCP) using the wiki article.

Am looking to see if I can customise them some more, and have been digging around and found snippits, but am wondering whether anyone has any experience they can help me with. In particular, I am trying to:

1 - Change the extension names (At the moment it says '201' and then '201' below it - would like it to say 'Kitchen' on screen, and that 'Kitchen' is calling when I ring someone). I've tried changing this in FreePBX and LinuxMCE but no joy.

2 - Disable push notifications to the orbiter function (am guessing this might be a generic orbiter option somewhere but I haven't found it yet? I know push is great BTW, just want to turn it off on one phone)

3 - Use the right hand context keys for direct extension dialling, AND line appearances if possible (ie I am extension 201, I can see 202 is on phone by looking at the screen, and when they come off the phone press it to call them)

4 - Any advice on background image - I read something somewhere about changing something in Asterisk but it concerned me the way it was worded in case it upsets LinuxMCE

5 - Also have read much on the 'SIP vs SCCP firmware' debate! Is SIP firmware working yet, or is it still best to stick with SCCP? It's working fine, so unless there's a reason to swap (call quality I think was mentioned on one page i read?) then I will stick with SCCP.

Thanks!
Tawny

Pages: [1]