Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - tortho

Pages: [1]
1
Users / Zwave device stops working and fails to restart
« on: December 05, 2010, 11:29:01 pm »
Hi,

Aeon Labs Zstick.
It just stops working from time to time.
When I try to do a quick reload router the device fails to start (Device 112 on my core)
From the log of the device I find nothing usefull.

Anyone with hints of where to start locking for what is going wrong?
Below the last lines in the log.
Can also see in old log files that there is a lot of lines with "No callback received: awaiting_callback: xx timer: xxxxxxx"

Device ZWave, # 112   
Device Template ZWave, device category Lighting Interface, manufacturer Pluto.   
4 lines, displaying from 0 to 4   
1   
05   12/05/10 7:42:10.294      Going to rotate logs... <0xb608bb90>
05   12/05/10 8:17:59.157      Going to rotate logs... <0xb608bb90>
05   12/05/10 21:47:53.953      Got a reload command from 0  <0xb608bb90>
05   12/05/10 21:47:54.203      void ClientSocket::Disconnect() on this socket: 0x9230350 (m_Socket: 7) <0xb708e6c0>

2
Users / RS232 & Sharp Aquos not working in LMCE, Only Windows
« on: February 22, 2010, 12:35:20 pm »
Hi,

On my laptop:
With windows running Putty I do control my Sharp Aquos LC52X20E with e.g. "POWR1   " & "POWR0   " or any other command from the manual.

On my Core:
Have 2 serial ports (one on the Motherboard which is not connected and one on a pci card which is connected to the TV)
Found the serial card which is connected to be /dev/ttyS1 (Port 0xdc00)
Only these 2 serial ports are reported with UART 16550A when I run setserial -g /dev/ttyS[012345678]

When issuing the below commands nothing happens:
/usr/pluto/bin/TestSerialPort -p 2 -P N81 -b 9600 -t "POWR0   \r\s500mPOWR1   \r\n" -i 1 -s "OK\r"

or

/usr/pluto/bin/TestSerialPort -p 2 -P N81 -b 9600 -t "POWR0   \r\n" -i 1 -s "OK\r"

Any suggestions on where the issue might possibly be is highly appreciated.





3
Users / Broken audio in .flv video files
« on: February 06, 2010, 10:58:50 am »
Believed that after upgrades last week playback of .flv files got broken.

Lots of noise, scratching sound on the audio and totally unusable of the video files.

Anyone else experiencing the same or have a workaround?

4
Users / ACT Homepro Z-wave ZRM230 Only partially working
« on: February 01, 2010, 12:42:06 am »
Hi,

Purchased a ACT ZRM230 light switch and was planning to use the "second" switch to turn off all my zwave devices.. but can not figure out how to get it working.

The "normal" switch works fine and is detected. Can the second one be "detected" in any way and be used in LMCE to control any of the other z-wave devices?
Using this together with Aeon Z-stick. (Assume I could have programmed it with another controller)

The device is here:
http://www.smarthus.info/redirect.php?action=url&goto=www.act-solutions.com%2FHomePro%2Fpdfs%2FHomePro%2FSpecs%2FZRM230_spec.pdf
http://www.smarthus.info/product_info.php?cPath=1_46_128&products_id=1884

Thanks!

Pages: [1]