Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - aggiemarine07

Pages: [1]
1
Installation issues / Re: Black screen after installation is finished
« on: July 10, 2008, 10:38:07 pm »
I know it may work for some but that didnt work for me at all; even after multiple reboots and different keyboards and even different monitors. So I used the method I stated earlier and that did.

2
Is anyone willing to go buy one for me? The nearest Circuit City with this deal is over 150 miles away (on the East Side of houston, TX). I am willing to pay for the shipping. Thanks!

3
Installation issues / Re: Black screen after installation is finished
« on: July 09, 2008, 06:14:30 pm »
Ok if your keys dont work whenever you get that blank screen, you might want to try this with a wired keyboard (just as a precaution). Keep in mind you dont want to hold down any keys:

Power on the computer
Kbuntu starts to load then you hear the first beeps (that to me sounds like an old cell phone ringtone)
it then finishes loading and that is where you get the blank screen, and you then get a second set of beeps

When you get the blank screen after this second set of beeps, hit enter

First we need to select what video type we want to do this you will need to press the down arrow key a certain number of times (depending on type):
For VGA - press nothing
For DVI/HDMI - press the down arrow key once
For Component - press the down arrow key twice
For Composite - press the down arrow key three times
For S-video - press the down arrow key four times

After youve pressed the down arrow key X amount of times you need to press the RIGHT ARROW KEY to move on and select your resolution:
If you selected VGA
640x480 (4:3) - press nothing
480p (16:9) - press the same key once
800x600 (4:3) - press it two times
720p (16:9) - three times
1024 x768 (4:3) - four times
1280x800 (custom) - five times
1280x1024 (5:4) - six times
1080p (16:9) - seven times

If you selected DVI/HDMI
640x480 (4:3) - press nothing
480p (16:9) - press the same key once
800x600 (4:3) - press it two times
720p (16:9) - three times
1024 x768 (4:3) - four times
1280x800 (custom) - five times
1280x1024 (5:4) - six times
1080p (16:9) - seven times

If you selected Component
HD480p - press press nothing
HD720p - press it once

If you selected Composite
PAL-B - nothing
PAL-D - press the down arrow key once
PAL-G - press it twice
PAL-H - press it three times
PAL-I - press it four times
PAL-K1 - press it five times
PAL-M - press it six times
PAL-N - press it seven times
PAL-NC - press it eight times
NTSC-J - press it nine times
NTSC-M - press it 10 times

If you Selected S-Video
PAL-B - nothing
PAL-D - press the down arrow key once
PAL-G - press it twice
PAL-H - press it three times
PAL-I - press it four times
PAL-K1 - press it five times
PAL-M - press it six times
PAL-N - press it seven times
PAL-NC - press it eight times
NTSC-J - press it nine times
NTSC-M - press it 10 times

Now that you have selected your resolution, hit the RIGHT ARROW KEY again to select your refresh rate. Keep in mind that you should consult your manual to determine your monitor/tv refresh rate correctly.

If you are using DVI/HDMI
50hz - nothing
60hz - press the down arrow key once
65hz - press it twice
70hz - press it three times
75hz - press it four times
80hz - press it five times
85hz - press it six times

***If you are using Component, composite, S-Video you do not need to select this setting.

After you have done all this hit the enter key and if you try what you set. It should work because all you are doing is navigating the menu "blindly."  The computer is projecting an image but you just cant see it because its in VGA. With this method as long as you have a keyboard (wired, not wireless, just for failproof sake) then this should work.

Let me (and others) know if this works or not. Thanks!

Pages: [1]