Messages

1

Installation issues / DTS / AC3 problem

« on: September 18, 2008, 08:24:51 am »

I have an issue with DTS and AC3 sound. In the AVWizard, i can hear both sound without any problem, the receiver (Yamaha DSP-Z11) switch between PCM, AC3 and DTS, so i use AC3/DTS pass-trough.
But when i watch DVD Playback with DTS sound, the receiver stay in PCM mode and i can only hear a "tchick-tchick-tchick".

My soundcard is an integrate intel ICH9 on a Asus P5K motherboard.

tks

2

Installation issues / Re: LMCE Crash

« on: May 22, 2008, 10:15:20 pm »

Thank's for your answer,
I have re install the system...
I think, it's a problem with vdr  http://forum.linuxmce.org/index.php?topic=4889.0
I have reinstalled with vdr, and now wait & see...

3

Installation issues / Re: LMCE Crash

« on: May 21, 2008, 06:12:00 pm »

In the admin web, Advanced / Configuration / Unknown Device, I have that :


Wizard | Unknown devices
#    Description    MAC Address    IP Address    Vendor model ID    Serial number    Device    Action
1       00:16:36:4e:a3:ad    192.168.80.251    DT:1837    \\192.168.80.251    1    
2             DT:1790    359e9932-d7ae-4546-9a60-21c75c227a41    1    
3             DT:1790    e29c8e9c-1f25-45e6-af17-c9c1ba2356b0    1    
4       ) Wed May 21 07:4    ) Wed May 21 07    DT:1837    \\) Wed May 21 07:41:28 CEST 2008 Reporting Wed [Wed] to the router Wed May 21 07:41:38 CEST 2008 Processing ) Wed May 21 07:41:28 CEST 2008 Reporting Wed [Wed] to the router May ) Wed May 21 07:41:28 CEST 2008 Reporting Wed [Wed] to the router (mac: ) W

I don't understand nothing...

4

Installation issues / LMCE Crash

« on: May 21, 2008, 02:59:57 pm »

I'm with 7.10 RC1 since few days, and it work nice.
But today my core was busy, i had message "done fileserver ... done fileserver" - "I detected a new P&P device .... fileserver hda1....". So i halt the core, but MD's don't stop (I forced them).
I boot my core and i have this message :
dcerouter_:/etc# dmesg | tail
[  795.392000]  CIFS VFS: cifs_mount failed w/return code = -6
[  796.180000]  CIFS VFS: cifs_mount failed w/return code = -6
[  796.324000]  CIFS VFS: cifs_mount failed w/return code = -6
[  797.052000]  CIFS VFS: cifs_mount failed w/return code = -6
[  797.200000]  CIFS VFS: cifs_mount failed w/return code = -6
[  797.928000]  CIFS VFS: cifs_mount failed w/return code = -6
[  798.072000]  CIFS VFS: cifs_mount failed w/return code = -6
[  798.916000]  CIFS VFS: cifs_mount failed w/return code = -6
[  799.060000]  CIFS VFS: cifs_mount failed w/return code = -6
[  799.784000]  CIFS VFS: cifs_mount failed w/return code = -6
dcerouter_:/etc#

With the launcher, I can't restart the MD hybrid and any other MD's.

Do you have any idea?

Thank's

5

Developers / Re: Home Automation EIB/KNX

« on: May 07, 2008, 08:25:26 am »

LMCE works only with RS232 interface FT1.2 like this http://www.eibmarkt.com/cgi-bin/eibmarkt.storefront/48214a72005abe02274450f3362b05e0/Product/View/N000250

6

Installation issues / Re: 32 bit MD

« on: January 19, 2008, 03:00:26 pm »

I have resolved my issues...
I go in advanced setting of media director, click on "view" for device template "Generic PC as MD", and valid "Allowed to modify" in Current Data #233 (+ save page).
In advanded setting i set "LMCE_MD_u0710_i386" in "Model" parameter.
I make a "Rebuilt Image" (maybe it's not necessary), Quick reload and my MD (Fiire Station) start.

But i have another problem. Fiire Station have a Via Unichrome Pro graphic chipset.
I can't start Xserver when "via" is setting in Xorg.conf.
I must set "vesa" to start.
I can't resolved this problem since i use LMCE. I have seen in mantis the same problem and i think that is resolved with 7.10 release.

Last question : When i add a media director, i can choose Fiire Station, but i never can boot with this config. When i boot with Fiire MD, I have red message "Failed Setup_config.sh". Do you have any explain?

Tks
 

7

Installation issues / 32 bit MD

« on: January 19, 2008, 12:42:13 pm »

I have install 710b3 64bit without any problem on core AMD Athlon x2, but i can't install MD 32 bit, the architecture is in 64 bit.

Do you have a solution for me.

Tks in advance

8

Users / Re: What HA Protocol do you (want) to use with LMCE?

« on: January 02, 2008, 07:34:41 pm »

EIB and KNX is the same protocol

9

Users / Re: Home automation

« on: December 21, 2007, 09:48:08 am »

In Europe, there is EIB/KNX bus for home automation. It work fine with LMCE.

10

Developers / Re: Nokia 770 Orbiter

« on: October 25, 2007, 08:21:45 am »

Problem resolved. It was download error for the 2 files...

11

Developers / Re: Nokia 770 Orbiter

« on: October 25, 2007, 08:10:42 am »

Hello,

I have a nokia n800 with OS2007.26-8, and i try to install pluto orbiter. I have installed all the depedencies (with repository) except libmysqlclient12 and libsdl-gfx1.2 : "unable to install ...".
When i try to install the package linuxmceorbiter-0704-03_armel.deb, it's notify application packages missing

Tks

Mickael

12

Users / Re: Web Bookmarks

« on: September 17, 2007, 09:02:21 pm »

Thanks ;-)

13

Users / Web Bookmarks

« on: September 17, 2007, 06:18:30 pm »

Hi,

How can i add new web bookmarks in the computing menu?

Thanks for answer

Mick

14

Installation issues / PlutoMO.sis

« on: August 30, 2007, 08:02:34 am »

I have a nokia n95 Symbian 60v3 and i can't install PlutoMO.sis. The phone says that PlutoMO.sis installation not supported.
There is no problem to install with nokia 6680 symbian 60v2.

Do you have any idea to do that?

tks